Panasonic AW-UE150 BLack – PTZ Cameras & Accessories

Yes. The UE150 outputs native 12G-SDI, which carries 4K 59.94p/50p and 1080p directly to your router, CCU, or switcher without transcoding. Confirm your router firmware supports 12G input; most modern Grass Valley and Sony systems do. For legacy 3G-SDI infrastructure, the camera also outputs 3G-SDI simultaneously, allowing parallel routing. Fibre output via SFP optical modules extends cable runs in larger vehicles without signal degradation.

The UE150 accepts Visca-over-IP and RS-422 serial control via its control port. If your RCP (Grass Valley, Vinten, or generic Visca controller) outputs RS-422 or IP-based Visca commands, it will operate the pan-tilt-zoom and presets. Confirm your RCP firmware matches Visca specification; Panasonic PTZ cameras are standard-compliant but edge cases occur with proprietary extensions. Request a control protocol datasheet from your vendor to validate compatibility before final order.

Partially. PoE++ (IEEE 802.3bt) supplies ~95W, sufficient for the UE150's nominal operation. However, in high-zoom and high-pan-speed scenarios, peak power draw may approach or exceed this; verify with load testing in your environment. For OB vans with existing 12V distribution, DC remains more predictable. PoE++ excels in fixed-install or multi-camera remote studios where centralised UPS-backed PoE injectors reduce power cable clutter and improve redundancy architecture.

The 20x optical zoom (F2.8–F4.5) preserves native 4K resolution and sensor light sensitivity across the range. Beyond 20x, UHD intelligent zoom (to 24x) applies sensor-level binning or algorithmic zoom, maintaining 4K output but with reduced apparent detail and slight noise increase in low-light scenes. Use intelligent zoom for framing adjustments only; if critical sharpness is required, limit to 20x optical. For FHD-only output, intelligent zoom extends to 32x with better fidelity due to pixel oversampling.

The AW-UE150 is video-only; it does not embed or de-embed audio on any SDI output. Audio must be sourced separately—either mixed in your router, switcher, or CCU, or distributed via independent AES/EBU or analogue pathways. This is standard for remote PTZ cameras but critical for OB workflow design: plan audio breakaway paths before finalising your production control room schematic to avoid last-minute cabling revisions.

The AW-UE150 is an active product in Panasonic's broadcast lineup with regular firmware support. Firmware updates (pan-tilt response tuning, protocol enhancements) are typically issued 1–2 per year; download and deploy via USB or Ethernet. Spare parts—IR receiver module, cable connectors, pan-tilt motors—are stocked by authorised dealers with typical 2–4 week lead times. For critical OB environments, negotiate spare-parts agreements or maintain a second unit as a hot-swap backup.

Yes, the UE150 includes NDI-HX V2 licensing for IP multicast or unicast delivery over standard Gigabit Ethernet, enabling flexible remote production and monitoring workflows. It does not natively output ST 2110; confirm your production control infrastructure supports NDI ingestion (vMix, OBS, Panasonic hardware mixers, etc.). For ST 2110 workflows, insert a media gateway or third-party converter. Verify your network QoS and bandwidth allocation—4K NDI consumes ~100–150 Mbps depending on frame rate and compression.

The UE150 ships with a bracket interface compatible with Panasonic's mount ecosystem and common third-party PTZ heads (Vinten, Sachtler, etc.). Verify your pedestal or jib's payload rating and pan-tilt damping; 4.2 kg is light enough for most broadcast pedestals, but confirm your head's tilt-down stability under pan acceleration. OB vans often use low-profile wall or truss mounts; ensure the bracket clears cables and allows unobstructed 360° pan and ±90° tilt before fabrication.

The AW-UE150 does not provide dedicated genlock or timecode input ports. Synchronisation is implicit via SDI output timing when cabled to a synchronised router or frame synchroniser, or via networked reference sync if using NDI output. For multi-camera switching with mixed fixed and PTZ sources, embed timecode in your router/CCU layer. If genlock-locked operation is mandatory (e.g., chroma-key or tight multi-image compositing), confirm with Panasonic whether your firmware revision supports external sync via serial control or recommend a sync hub to align all sources upstream of the switcher.

Yes. Our used and ex-demo units undergo a full functional inspection — sensors, video outputs, control signals, optics and mechanics — including a colorimetry and sensitivity test. Each product is tested by our technicians and comes with a 90-day warranty. Contact us for the specific warranty terms of the unit you are interested in.